日本人一级毛片免费完整视频

  日立中央空調不制冷?可能是銅管泄露造成的！下面云南日立中央空調的小編給大家闡述一下：銅管泄露是日立中央空調的致命缺陷，一旦泄露，空調的制冷劑將全部溢出，空調由于缺乏傳熱介質而使 空調器失效。

  1、制造方面的原因
  我國標準規定了銅管必須進行渦流探傷。這項要求在正規大型銅管廠是能夠充分保證的，因為探傷是通過在線檢測的。有的銅管廠則不是這樣，不經過渦流探傷或者是用低標準的渦流探傷儀抽檢，這樣銅管就存在超標的缺陷漏檢，或未檢測造成安裝日立中央空調使用時空調制冷劑泄露。

  2、安裝的問題
  在安裝云南日立中央空調的過程中要經過彎管、漲管、擴口、焊接等環節。在彎管的過程中由于彎曲部分要經過局部受力，造成局部的過拉伸，形成開裂、暗裂等問題，一旦充填制冷劑，往往在此處發生制冷劑泄露。銅管穿過翅片后，要在漲管機上漲管，漲管的過程極易出現漲頭劃傷銅管，形成穿透傷造成銅管泄露；有時由于鋁箔內孔的毛刺過大，在漲管的時候毛刺刺透銅管造成泄露。

  3、銅管本身質量問題
  云南日立中央空調銅管本身質量的原因可以分為外表面缺陷、內表面劃傷、內表面氧化等。銅管在漲管、擴口的冷加工變形中，表面受拉應力而伸長，當銅管外表面有深度傷痕時，銅管外表面承受不了表面拉應力，形成拉斷現象，也就是我們看到的銅管外表面開裂。銅管內表面有氧化時，在漲管時由于氧化銅管內表面的摩擦力與沒有氧化銅管內表面的摩擦力不等，造成相同長度的銅管下墩長度尺寸不一致，擴口時下墩量小的銅管伸出長度長，造成擴口過大而開裂。

  4、焊接方式的問題
  云南日立中央空調銅管在連接起來的過程中，需要用焊料將分歧管與銅管焊接在一起，焊接方法分為充氮焊接與不充氮焊接兩種。一般會選擇充氮焊接，充氮焊接可防止焊口產生氧化物，經過長期的制冷劑系統循環，不充氮焊接會導致焊口氧化物脫落造成管道臟堵，最后造成壓縮機的損害。不但影響了制冷效果，嚴重的還需要對壓縮機進行維修或更換。

  以上四個方面就是日立中央空調銅管泄露的原因，當你家的日立中央空調不制冷時，很有可能就是銅管泄露了，此次你應該找日本人一級毛片免費完整視頻:云南日立中央空調安裝公司為你維修。